Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser that works with CAN buses. It is discrete, does not use LED indicators or key fobs, and is concealed in the wiring of the vehicle.
The user can also deactivate the system temporarily using Transport Mode when renting out their car. This guide will take you through the process of installing a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a modern security device that guards your vehicle from hacking, key cloning, and relay attacks. The system is directly connected to the ECU of your car and protected by a PIN code you select. It's undetectable to thieves using diagnostic scanners or other advanced methods, and is unable to be disabled through circuit cuts.
The system is easy to use, however it's essential to use a an expert installation to ensure a smooth and secure connection to your vehicle's ECU. A Thatcham-approved installer can help in the installation and programming of your Ghost system. They can also suggest a tracking system or alarm system to complete your vehicle's protection package.
The first step is to disconnect your battery in order to avoid accidental airbag deployment or short circuits. After that, the installer can safely begin work. Basic hand tools are useful for making precise connections, while a multimeter can be used to test the electrical properties and safety. Cable tie and insulation tape are essential to protect connections and ensure that wiring is neat. The user's manual provides specific guidance tailored to the Ghost Immobiliser model you have.
During the installation process, it's crucial to select a grounding point that's free of debris and paint. The installer should be sure that the immobiliser's H and CAN L wires are connected to the appropriate ports on your vehicle's ECU. The wires can be plugged into or soldered, depending on the model. A top-quality connector is recommended to ensure a long-lasting and secure connection.
Transport Mode can be turned on by the customer once the installation is complete. This permits mechanics or valet parking to access the vehicle without knowing the pin code. To do this, the customer has to hit the service button on the dashboard five times in a matter of 2 seconds. Once this is done the system will verify by displaying 5 signals.
The Autowatch Ghost 2 immobiliser is TASSA approved and is a highly efficient immobiliser. It's an excellent option for those who regularly rents out their cars through platforms such as Turo. Immobilisers can lower the cost of insurance, as it decreases the likelihood of theft.
Getting Started
You won't have a problem using an autowatch immobiliser in order to guard your car from thieves. It will stop your car from being started if a criminal steals or copies the key. This is due to its sophisticated technology, which is designed to prevent the engine from running without the correct PIN code is entered.
The device is connected to the vehicle's bus system CAN which allows direct communication with the ECU. It uses buttons that are already present on the dashboard and wheel to create a unique sequence that only you can identify which makes it impossible for others to start your car. This is the most secure security system to protect your most precious possessions and will ensure its value in the event that you decide to sell it in the future.
Installing a ghost ignition is a simple process, but it is crucial to follow the directions carefully to avoid issues with electricity and system malfunctions. First, you must find a 12V power source and a suitable grounding for the chassis of your car. Then, you can start connecting the wires to the immobiliser. Be sure to use high-quality connectors and soldering methods to ensure a strong connection. Also, be sure to protect the connections by insulating them with heat shrink tubing and insulation tape to protect them from electrical short circuits and other problems.
After the wires are connected, you can plug in the battery and start the engine to determine whether the immobiliser works. After you've confirmed that everything is working properly then you can put the immobiliser in a safe place inside the vehicle. Be sure to conceal it in a secure manner so that thieves can't alter it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified This means it complies with the highest standards of security and is a fantastic deterrent to car thieves. It provides superior protection against key cloning, hacking and relay attacks, and isn't able to be disabled unless you know the code. It is also simple to use and can be set into a service valet mode so that your car isn't activated if you bring it in for servicing or an MOT.
Wiring
The Ghost Immobiliser is a cutting-edge security system designed to prevent vehicle theft. It connects directly to the vehicle's CAN bus network and communicates with the ECU which makes it virtually undetectable to your car. In contrast to other aftermarket systems that require the removal of circuit components The Ghost Immobiliser does not interfere with any of the factory settings of your vehicle.
The system is also unnoticeable by thieves using diagnostic scanning tools. This is because the system doesn't send and receive radio frequency signals and it uses the CAN data to communicate with your ECU. Additionally, it doesn't require any modification to your car's existing key fobs.
Enter your disarm sequence (either two or one buttons) and then switch on the ignition of your vehicle to activate the Ghost Immobiliser. The indicator will flash twice to confirm that you've entered the correct code. You can now start your vehicle and drive in a safe manner.
Once installed The Ghost Immobiliser can secure your vehicle from hacking and key cloning and will also protect the value of your pride and joy. In Transport Mode, you can temporarily disable the Ghost Immobiliser when you need to give your car to service or valet parking.
You'll need a constant power source (12V) in addition to an earthing point to complete the installation of a Ghost immobiliser. Be sure that they are well-insulated and safe to touch. Cable ties are also suggested for bundling and secure the wires. This reduces the risk of theft by thieves. Be sure to verify the position of these points to avoid mistakes and mark them with the help of tape or a label. It's important to check every connection for signs of wear and tear. Be sure to ensure that all connections are firmly in place and properly insulated. Make sure to test your Ghost Immobiliser after the installation is completed. This will ensure that the unit is operating correctly and that all connections are secure and insulated. Be sure to fix any issues immediately.
Testing
The Autowatch Ghost Immobiliser is an innovative vehicle security system that seamlessly into your car's ECU to prevent unauthorised engine start. Its cutting-edge technology protects your vehicle from hacking and key cloning as well as other methods commonly used by thieves to steal vehicles. The Ghost works in conjunction with existing tracking and alarm systems to provide the most effective protection for your vehicle. The Ghost's unique features, combined with its subtle design, make it a popular option for both car enthusiasts as well as security-conscious drivers.
To ensure proper integration of the Ghost Immobiliser, it is essential to follow every step of the installation procedure. Check the wiring diagram of the vehicle to help you locate and connect the wires. You'll need to determine the power and grounding sources. Once you have located them, you'll need to mark the points to make them easy to identify during installation. It is also essential to use high-quality tools and materials. Basic hand tools can help with making precise connections while a multimeter can confirm electrical values and guarantee safety. Insulation tape and cable tie will keep all connections neat. A Ghost-specific user's manual is also available.
It is crucial to test the system prior to installing it. Enter the PIN code into the system, and then start the vehicle. This step will confirm the immobiliser is working as it should and prevent unauthorised vehicle starts. This procedure should be carried out regularly as part of your routine vehicle inspections in order to ensure that the system is always functioning properly.
After the installation is completed Once the installation is complete, you can drive your vehicle with confidence. The Ghost will safeguard your vehicle from potential car thieves. It will ensure that no one is able to take your car away without having the correct PIN code. The Ghost can be used in conjunction with an approved Thatcham tracker that detects any attempts at theft or tampering. This will allow you to track your vehicle if it is stolen.
car immobiliser ghost can be utilized on a variety of vehicles and is compatible with all major manufacturers. If you're interested in protecting your car with this cutting-edge device, call Monty's Locksmith today to learn more about our installation and service options. We are a TASSA registered installer, which ensures that we adhere to strict standards for installing our products. This assures customers, insurance companies, and law enforcement that all installations are performed in a safe and correct manner.